|
Cut the Red Tape
Call 616.786.3980
Fax 616.786.0299
| |
KORODUR WH-Metallic
KORODUR WH-Metallic = Hard Aggregate acc. to DIN 1100-m
0/4.
Hard metallic aggregate for surfaces which are subject to
the most severe stress which require high tensile strength together with a very high wear
resistance.
Areas of Application:
For all hard aggregate concrete screeds acc. to DIN 18 560
(1990) - ZE 55 M.
Extremely resistant to bumping and ramming stresses.
Especially suited for areas with heavy iron wheel traffic, rolling and impact abrasion of
sharp-edged machinery etc.
For the production of "armoured paving".
Properties:
 |
resistant to petroleum, oil, solvents
|
|
highly wear resistant even under the most severe stress,
fork lift-truck resistant
|
|
water-resistant, suitable for use in wet rooms
|
|
non-skid, anti-slip even when subjected to oil spillage and
in wet rooms
|
|
de-icer resistant
|
|
non-rusting
|
|
not harmful to health
|
|
not electrostatically chargeable
|
|
easy to clean
|
|
improved surface density
|
Technical Data
Coating Group DIN 1100 - Coating Group M
|
Technical Data of hard
aggregate acc. to DIN 1100
|
Specified Values of
hard aggregate screeds acc. to DIN 18560-ZE 55 M
|
acc.to DIN 1100
coating group M
|
acc.to test certificate
external control
DIN 1100
KORODUR WH-Metallic
|
quality test
|
confirmation
test
|
Tensile strength N/mm2
2
nominal strength (smallest single value)
serial strength (avg. value)
|
-
min. 12
|
-
13,0
|
-
>=11
|
>=10
>=11
|
Compressive strength N/mm2
2
nominal strength (smallest single value)
serial strength (avg. value)
|
-
min. 80
|
-
95,0
|
>=55
>=70
|
-
-
|
Wear cm3/50 cm2
2
nominal strength (greatest single value)
serial strength (avg. value)
2
nominal strength (greatest single value)
serial strength (avg. value)
|
max. 5,5
max. 5,0
|
-
4,1
|
<=4
<=3
|
-
<=4.0
|
Bulk density kg/dm3
|
without norm
|
1,68
|
-
|
-
|
Granulometric composition
|
acc.to DIN 4226
|
acc to DIN 4226
|
-
|
-
|
Qualification test values = DIN 1100-values, screed test
values = DIN 18 560 (1990)
Group of Mechanical stress acc. to DIN 18560 (1990)
Part 7, Table 1
Stress Group
|
Mobile industrial handling equipment, kind of
tires1
|
stress caused by operational processes and pedestrian
traffic.
|
I (heavy)
|
steel and polyamide
|
processing, grinding and sliding of machinery, placing
down of goods by means of metal forks, pedestrian traffic of more than 1000 persons/day
|
II (medium)
|
urethane-elastomer and rubber
|
sliding and rolling of wood, paper rolls and plastic
castings, pedestrian traffic of 100 to 1000 persons/day
|
III (light)
|
solid tires and pneumatic tires
|
assembly areas, pedestrian traffic up to 100 persons/day
|
1 Refers only to clean tires.
Commpressed grit, swarf and dirt on tires increase the stress.
|
Remarks: Where the loading and abrasion
potential is beyond the guidelines for "Stress group I", e.g. assembly of
heaviest equipment or traffic of heaviest vehicles (crawlers) special precautionary
measures must be taken.
Note: Please contact Technical Department for advice.
Processing and Consumption
per m2 according to instructions
Stress Group
acc. to DIN 18560 (1990) Part 7 Table 1
|
Topping Thickness
acc. to DIN 18560 (1990) Part 7 nominal thickness
|
Mixing Ratio
1 w.u. cement : 3 w.u. KORODUR WH-Metallic
|
I (heavy)
|
8 mm
|
21 kg/M2 KORODUR WH-Metallic
|
II (medium)
|
6 mm
|
16 kg/M2 KORODUR WH-Metallic
|
III (light)
|
6 mm
|
16 kg/M2 KORODUR WH-Metallic
|
|
|
